Tampilkan postingan dengan label DIY. Tampilkan semua postingan
Tampilkan postingan dengan label DIY. Tampilkan semua postingan

Rabu, 31 Juli 2013

Staircase nook

Hey hey all! Well, it’s about that time! I’m off to Atlanta today to prepare for the Haven Conference that starts tomorrow. It’s been a year of planning and I can’t even believe it’s already here! SO excited to see everybody.

So I finished up a quick little project this week that I’ve been meaning to do for months. Or a year. A year and a few months.

We have a little ledge/nook/cut out spot in the basement staircase that has been sitting half way done for that year and a few months:

You may remember that I installed a wood wall on the main wall in the staircase about this time last year. I still LOVE that wall. So very much.

Before we had the basement finished the wall next to it going down the steps had a weird cement wall bump out thing. Instead of drywalling all the way up I asked them to make it a little ledge instead. They installed a wood piece that I was planning on painting later, hence the stain spatter I didn’t worry about:

But since then I’ve decided I wanted it stained instead. I’m kind of obsessed with the look of the dark wood against the gray blue walls (Marina Gray by Ben Moore) and white trim down there.

So I needed to sand off that stamp and the stain dots:

sanding before staining

It just took a few seconds and I was ready to go – then I taped everything off with my Frogtape really well. I find it’s hard to keep stain from going everywhere since it leaks easily and spatters all over the place. (It could be the operator, who knows.):

prepping for stain

After I wiped everything down well (and let it dry), I grabbed my dark walnut stain and went at it:

how to stain

Remember when you stain to work quickly and to keep the “wet edge” – if it dries at all during the process you’ll see where you left off. OH, and wear gloves!! Trust me – no matter how hard I try I always end up with stain on my hands.

I let it sit for a few minutes and wiped the excess off. I only usually do one coat – I find that’s plenty for the color I want.

While it dried I started hanging the frames I’ve had leaning there forever. Most of them are pics from the Macy’s Thanksgiving parade/NYC trip I showed you here, but there was one collage my stepdaughter gave us last Christmas (so sweet!) that I wanted to include too.

Here’s a little tip when hanging pics that have two hangers instead of one – just tie a piece of string or wire between the two:

hanging picture without a level

Then hang that on the the nail. SO much easier. I mean, sometimes what you’re hanging is heavy enough you’ll want two nails, but most of the time I find one is just fine. And this way you don’t have to worry about measuring, finding a level, all that stuff. Ain’t nobody got time for that.

Like all of my gallery walls, I just kind of put stuff here and there – yes, that meant a few extra holes in the wall but they’re tiny. The wall will survive:

matching frames gallery wall

I was trying to use frames that I had on hand and I liked the (mostly) matching frames, so I didn’t go crazy trying to fill empty spaces. The “S” we’ve had for years and it perfectly filled one spot that was bugging me.

The ledge has plenty of room for accessories, but for now I just left a couple candlesticks we had here before (they ended up on there because I was too lazy to take them all the way to the storage room):

matching frames gallery wall

They are fake candles and they operate on a timer, so it’s kind of cool to have that little glow as we walk down at night.

It was a quick project and I think it turned out pretty cute! I love how it looks with the planked wall:

wood planked wall

Next up in this space – touch up the wall and ceiling paint and install chunkier baseboards. Maybe I’ll tackle those in another year. Baby steps.

So are you loving gallery walls? I am and I don’t think they’re going anywhere soon. It’s such a personal, easy way to fill wall space! And remember you can find frames at Goodwill for super cheap and spray paint them. One color for all of them will unify frames no matter their design. 

Rabu, 24 Juli 2013

DIY tufted headboard tutorial

Hello all! I’m so excited to share more about how I made the new headboard in our bedroom. I shared more about the start to this room redo, the new bed and the headboard earlier this week.

I’ve made my own headboards (and for friends!) for years – even before blogging. It’s seriously one of the easiest DIY projects you can do and you will save SO MUCH money doing it on your own.

The headboard part I was used to – but I was totally intimidated by the tufting part. I’ve never tufted one because it seemed like it would be hard…but it is not a big deal! For real, it wasn’t bad at all.

So here we go – I new the shape I wanted the headboard to be for awhile, but I just found out the other day that it had a name:

different shapes of headboards

I wanted the Belgrave look, which was totally easy to DIY. First up, Dad came down and we used his truck to pick up a big piece of mdf at the hardware store – it was a big four by eight foot piece and the Lowe’s Guy cut it down for me:

DIY tufted headboard

I wish I would have taken pics of how I cut the corners out, but it was so quick. Dad and I just searched the garage for something round (and used my bird food holder). I held it up on the corner and figured out how big of a cut out I wanted, then did some quick measurements to make sure it was even on both sides. Then I traced the bottom of the can and cut one side out with the jigsaw. That first piece is all you need to make the second one – just flip it over and place it on the other corner, trace, and you’ve got a mirror image.

I hope that makes sense – it was so fast I didn’t even think to take pics.

Dad helped me take the board upstairs where I went to work! I showed you how I made the headboard in the Bub’s room and this was nearly identical till I got to the tufting part.

Like that one, I used mattress pads instead of foam from the craft store:

foam mattress for upholstered headboard

Why this instead of regular foam? One word – cheaper. ;) Foam is a petroleum based product, so it goes up with the price of gas. Which means it’s just going up and up over time. I haven’t even check the price lately but for three inches of foam for a nearly 80 inch headboard wouldn't be cheap. The size was another reason – I would have had to use numerous pieces of foam to cover this and when you use the mattress pad you can get one big piece.

I had one I had picked up on clearance years ago (look for the XL twin sizes after back to school – you can find them for cheap!) but it was too small for this headboard. So I ended up with a bigger size (queen I think?), then ended up going back to get another one to do two layers because I really wanted it super soft.

One of the things I grew to dislike about our old headboard was how hard it was. I mean, it was wood, so yeah. And it had a curve to it so our heads never fit against it. First world problems. This time I made the headboard tall and cushy that we could comfortably lean against it.

Once the foam is down, you want to secure it with a layer of batting or thin fabric. I used batting first just because, again, I wanted this super soft. And I already had some, so that helped too:

DIY tufted headboard

Then I used a piece of muslin I had in my stash too, to cover everything again. This just secures all the foam and gives you a nice base for the final fabric.

Speaking of that – after all that I was ready to finish it up – and because I was feeling lazy and didn’t want to drive the extra 15 minutes to the fabric store, I actually shopped the drapery aisle at Target:

I wasn’t sure exactly what color I wanted so I grabbed a few. ;) The two on the left were $17 for a panel – which compared to a couple yards of upholstery fabric is pretty good.

Problem was we weren’t crazy about any of them when we tried them out. One was too light, one was too blah and one was too dark.

Soooo…the next day I went to the darn fabric store. ;) I needed the stuff to tuft the headboard anyway (at first I wasn’t planning on tufting. Scared, remember?) so I took a quick look through the fabrics and found one I LOVED in the suit fabric aisle.

Before I used that I figured out where I wanted my tufts and drilled the seven holes:

DIY tufted headboard

I just wanted it to be a simple design and some of the tufting I see is just too much for me. So when I did my math I decided to just do three across the top and four under that. That’s it – anything lower would always be covered by pillows or the mattress so I didn’t even worry about the bottom.

After the holes were drilled I added the final fabric:

DIY upholstered headboard

By the way, years ago I tried the electric stapler you can find at the hardware store (about $30) and it is kind of a pain in my butt to use. It gets jammed and the staples don’t go in evenly no matter what I do. I always revert back to my regular stapler (above) – it takes more muscle but that’s good for ya. ;)

Sometimes the corners can get tricky, so I’ve always used a simple method – start with the middle, then each side, pulling tight each time:

upholstering corners of headboard

For the curved corners I just grabbed the fabric and stapled as best I could:

upholstering curved corners

Remember…no one will see this part. Seriously, the back doesn’t matter. Do what you gotta do!

Here is is in it’s (almost) finished state:

DIY upholstered headboard

Getting there! The suit fabric is like a gray linen and looked so good. Way better than the drapes I picked out – I returned those.

Now the part I dreaded…the (shiver) tufting. So not hard. At all. All the stuff I needed was in the same section at Joann’s. I picked up this waxed thread and it rocked:

wax thread for tufting

It made this SO easy. More on that in a minute.

I grabbed some buttons too – it’s so easy to make your own fabric-covered buttons:

DIY buttons

I just used scrap fabric to make them all. Making buttons is fun.

So the tufting was a breeze – I couldn’t believe I had put it off all this time! I did poke myself a couple times, but overall, easy. :) First up, I threaded one of my long upholstery needles and made a little knot at one end, then stapled it to the back of the headboard:

how to tuft a headboard

Then I pushed the needle through the headboard, threaded the button on, and pushed it back through to the back. This is where the waxed thread comes in super handy – it kind of held the button where it was while I secured it to the back. Regular thread would slip and be hard to keep where you want it. This worked GREAT.

I would just put a staple in the back of the headboard, but wouldn’t push super hard on the stapler, so it didn’t go all the way into the wood. Then I was able to wrap that thread around it a few times, then hammer it down to secure it. (Pic on the right.)

I didn’t pull each button super tight – I didn’t want it to be a deep tuft. Just a little bit of tuft. And there is an easier way to do this by the way – you can just thread both ends of the thread on the needle with the button already on it, then put it through from front to back and then secure. But that method didn’t work for me because the waxed thread was so thick.

I was THRILLED with how it looked! I finished it up with some nailhead trim along the sides:

The particle board I used to make the headboard was 1/2 an inch thick and I went that size on purpose – so these would have something to grab onto. Any thinner and it would have been hard to get them in well.

I’ve never used the connected nailhead trim (I usually just do them individually) but wow, this made it so simple! The nailhead stuff is $21 for five yards, but I had two coupons so I got it for about $10. :)

I hung this up the same way I did in the Bub’s room – I just used picture hanging jobbies:

hanging a headboard

I figured out where the studs were and screwed into those in first, then that determined where I put the hangers on the back of the headboard.

When we got it hung I was so dang happy with how it turned out!: diy tufted headboard

You can see the nailhead trim better in that pic. From the front you don’t see it as much, but it’s a great little detail when you get up closer. I love it!

You can see there why I didn’t add any buttons any lower too – they’d just be covered.

Many of you have asked about the new bedding – I found it at HomeGoods earlier this year:

It’s by Hillcrest and it was a duvet cover and shams for $40. I had been looking for new bedding for months and just happened to find this, new sheets (they aren’t on now – they are darker and I’ll put them back on later in the fall) and the small pillow on the bed all in one trip. None of them are supposed to go together but I think they work well!

So far with what I made on the old bed, I’ve still got about $300+ to spend – I think I may make money on this redo! That’s what I’m talking about.

You can find upholstered and tufted headboards all over the place, but I promise you they are not hard to make on your own! It does take some time so just be patient with it. But you will save tons if you DIY this one -- the Pottery Barn bed on the left is $1000 for a king (gulp), the Ballard Designs on the right is $500+:

 Pottery barn upholstered headboard ballard designs camden headboard

I think mine looks pretty darn good for less than $100:

DIY tufted headboard

Here’s the break down on cost:

Wood: $15
Foam: $45
Fabric: $8
Buttons, nailheads, etc: $25

Total was $93! Aww yeah. And I have wood, foam, nailheads, buttons and thread left over to use on future projects.

If you went with one layer of foam/egg crate that will go down about $20. I had the batting and muslin but only one of those is really needed and they are both cheap. Of course of you skip the tufting that will help too!

Overall I’m so happy with how it turned out. And it is SO much more comfortable than our old headboard. Have you ever made your own? Did you find it easy to do? Have you ever attempted the tufting? Are ya sceered? 

Rabu, 26 Juni 2013

Too many spoons in the kitchen

Heyyyy all! How is your week going?

So you get that play on words? Cooks in the kitchen? Spoons? Well…maybe by the end of this post it will be clever.

I’m SO happy to be done with the powder room – have I mentioned that?? There’s a million reasons (hello…functioning bathroom) but one of the big ones is that I can finally start addressing some of the other little projects around the house. I told myself I would hold off until I got the bathroom done.

I told you a few months ago that I’m slowly but surely attacking the clutter hot spots around our house. At this rate I’ll be done next year in time to start it all over again, but whatever.

I’m on a mission in our kitchen to declutter the countertops. Mostly – not completely clear them off, but be smarter about the things we have out. I know it’s probably silly but lately all the utensils next to the stove were driving me crazy:

Especially considering we have a drawer right there that I use for the rest of the utensils:

utensil drawer organization

Problem was, as you can see – it was a hot mess. Every time I’d put something away I would have to try to close the drawer about five times before I finally got it shut. ;)

I realized it was getting a little ridiculous – who needs all those spoons? Really? Especially for someone who rarely hardly ever occasionally cooks? So I took about 15 minutes to declutter the situation.

You’ll notice the wonky drawer organizers in that pic above – that was a little DIY project I did years ago. (I saw the idea at Stephanie’s site here.) At the time I didn’t secure them well enough so they weren’t working so great.

All I did was take scrap wood from the garage and cut it to the width of the drawer and then nail it in. Stephanie just used glue for hers but that didn’t hold well enough for me. So I needed to add one more nail to each side to make them more secure and I used the little trick I used years ago:

utensil drawer organization

I used my Frogtape to mark off where the wood was so I could nail into it without missing. Does that make sense? Cause otherwise this happens:

(The nail didn’t hit the wood and came out the side.)

Obviously you still need to have good aim. Gah!

In hindsight I wish I would have installed the wood slats the long way instead of across, but if I remember right I was trying to work with scraps of wood I already had.

So once the organizers were secure again I started the purging and reorganizing. The bigger items went into a cabinet in the kitchen with like items and all the grilling stuff went outside underneath the grill:

By the way, those little marshmallow sticks telescope out and are perfect for making smores! :) I got them at the Target dollar spot last summer, not sure if they still have them.

We had doubles and triples of plenty, which I pared down. And then I found things that I have NO idea why we had:

Uhhhh…what are those?

I was able to purge plenty so now I don’t even need the holder next to the stove anymore, which was my goal:

gumball fish bowl

On a side note, Squish the Fish is doing AWESOME! We’ve had this Squish for three years now and he’s the most spoiled fish I’ve ever known. My husband loves him. You can see more about the gumball fish tank here.

But let’s marvel at the lovely utensil drawer, with a (little) room to spare:

utensil drawer organization One drawer done, eleventy billion to go.

And one thing you don’t ever think you’ll do until you blog – take a picture of your utensil drawer and share it with the world.

This little spot makes me feel like I did a lot – I find decrapifying is a lot more manageable when I tackle little bits at a time.

So do you have too many spoons in your kitchen? Can you close your utensil drawer??

Jumat, 21 Juni 2013

DIY nautical oar art

HEY there! Thanks SO much for all the lovely comments on the powder room post! I’m working on answering your questions so stay tuned if I haven’t gotten back to you yet!

I wanted to show you how I made over one of my favorite parts of the room (there are a lot of them) – the boat oar I found at a vintage mart a few months ago:

vintage boat oar redo

I first showed it to you in this post and as of a few days ago it still looked like that. :) This little redo seriously took about 20 minutes, and that was with paint drying!

I started out by wiping it down to prep it for paint:

vintage boat oar redo

I let it dry and then mixed some white paint (I used my CeCe Caldwell stuff, but regular white paint would do just fine. Flat may work better for this particular look.) with a little bit of water:

vintage boat oar redo

I didn’t want the oar to be covered completely – I wanted it to have a “wash” kind of look and this did it:

paint mixed with water for a wash

The nice thing is when it’s watered down a bit it takes even less time to dry. :)

I let it dry about ten minutes, and then used my delicate FrogTape to start marking where I wanted my stripes:

vintage boat oar redo

That one was on the handle -- I just searched striped boat oar images and kind of winged the design.

I taped off each section, painted and took the tape off immediately. I did that just because I knew even though the paint was dry to the touch it wasn’t cured and the tape may remove it. I take my tape off right away whenever I do stripes anyway so I get a really sharp line.

I moved on to the wider part and did a little stripe first:

vintage boat oar redo

When I pulled off that tape it did pull up a little bit of the paint, but I actually liked the look so I didn’t worry about it. I didn’t want it to look perfect anyway. ;)

Then I made a wider one in the middle:

nautical stripes boat oar

You can see there that I cut the FrogTape down the middle for skinnier pieces. Since I was working so fast I didn’t want to put the tape down over the red paint I had just done – this allowed me to keep working quickly. :)

I did all the red stripes, hung the oar in the bathroom and then realized I wanted to pull in some of that blue tone in the room. I had it over at the vanity/sink, but everything around the toilet was red.

So I grabbed the blue paint I used on this post (it worked perfectly!) and added a few more skinny stripes:

nautical stripes boat oar

I gotta be honest…I squealed a little when I saw how it all finished. ;) It was so stinkin’ cute!:

nautical stripes boat oar

I think adding that little bit of blue was a good call – it ties the whole room together!

To hang it I just nailed a picture hanger thing to the back of the handle at the top.

In the real life you can see much more of the bottom of the oar because you see it from higher up than in the pics:

wood planked wall bathroom So that’s how the cutest little oar art came to be! It was super fast and I used paint I already had – the oar itself was $10. Love it!

The room isn’t exactly nautical themed but I think it still works – you don’t need to follow a specific theme to make something you love work in a room!

Thanks again for all the sweet comments my friends! Have a GREAT weekend!